Category: question bank

CE6404 question bank SURVEYING 2 REGULATION 2013 Anna University

Post author By Mr. Padeepz
Post date February 27, 2018
No Comments on CE6404 question bank SURVEYING 2 REGULATION 2013 Anna University

CE6404 question bank SURVEYING 2

CE6404 question bank SURVEYING 2 REGULATION 2013 Anna University

Sample CE6404 question bank:

1. Triangulation :

Triangulation is nothing but the system consists of not of interconnected triangles. In this method, knowing the length of one side and three angles, the length of other two sides of each triangle can be computed.

2. Satellite Station :

A subsidiary station is established as near the true or principal station as possible, the station so established
is called a satellite station or eccentric station or false station.

3. Reduction to centre:

If the true station were occupied by computing the corrections and apply them algebraically to the observed
values is generally known as reduction of centre.

4. Base net:

A series of triangles connecting the baseline to the main triangulation is called base net.

5. Bench marking :

It is a fined reference point of known elevation.

6. Types of Bench Mark:

Great Trigonometric survey Bench mark
Permanent Bench mark
Arbitrary Bench mark
Temporary Bench mark

7. Equipments used for base line measurement:

Marking stakes or tripod
Straining device
Supporting stakes or tripod
Steel tape
Six number of thermometer.

8. Signals :

A Signal any object such as a pole target erected at a station upon which a sight is taken by a observer at another station.

9. Mistakes (or) Gauss Errors:

Depends upon the observer, a mistake cannot be corrected unless the observer get training. The mistakes are errors that arise from inattention, inexperience, carelessness and poor judgement of confusion in the mind of observer.

10. Conditioned Quantity:

It is the one whose value is dependent upon the values of one (or) more quantities. Its values bear a rigid relation to some other quantities. It is also called
“dependent quantities”.

Subject Name	Surveying 2
Subject Code	CE6404
Regulation	2013
File	pdf

CE6404 question bank 1 click here to download

CE6404 question bank 2 click here to download

For CE6404 Syllabus click here

CE6404 Notes click here

For CE6404 important questions click here

question bank

CE6403 Question Bank APPLIED HYDRAULIC ENGINEERING Regulation 2013

Post author By Mr. Padeepz
Post date February 27, 2018
No Comments on CE6403 Question Bank APPLIED HYDRAULIC ENGINEERING Regulation 2013

CE6403 Question Bank APPLIED HYDRAULIC ENGINEERING

CE6403 Question Bank APPLIED HYDRAULIC ENGINEERING Regulation 2013

Sample CE6403 Question bank:

1. Differentiate open channel flow from pipe flow.

2. What is specific energy and is the condition for getting only one depth for a given specific energy?

3. How will do you distinguish between critical, sub- critical, super- critical flow.

4. Sketch the velocity distribution in a trapezoidal channel.

5. What is the use of a pitot–tube?

6. Briefly write a note on anemometers

7. Find the relationship between Chezy’s ‘C’ and Manning’s ‘n’.

8. Sketch the velocity distribution in rectangular and triangular channels.

9. What are the possible types of flow in open channel with respect to space and time?

10. What are the equations for critical depth for rectangular channel?

11. Distinguish between steady uniform flow and unsteady non – uniform flow.

12. Define specific energy.

16 MARKS

1. Define specific energy of flow at a channel section. Draw the specific energy curve and explain.

2. A trapezoidal channel has side slopes of 1 horizontal to 2 vertical and the slope of the bed is 1 in 2000. The area of the section is 42 m2. Find the dimensions of the section if it is to be most economical. Determine the discharge of the most economical section of C = 60.

3. Describe various types of flow in an open channel.

4. A rectangular channel with a base width of 0.60 m carries a discharge of 100 lps. The Chezy’s C is 60. If the depth of flow is 0.25 m, determine the bed slope of the channel

5. A rectangular channel 1.5m wide and depth 2.25m, discharge is 10m3/sec. calculate the specific
energy and depth alternate to the given depth.

6. A trapezoidal channel has a bottom width 6m, and side slope of 2h to 1v if a depth of flow is 1.2m at
a discharge of 10m3/sec. compute the specific energy and critical depth.

7. Define wide open channel and also what are the important assumptions in hydraulic parameters?

Subject Name	APPLIED HYDRAULIC ENGINEERING
Subject Code	CE6403
Regulation	2013
File	PDF

CE6403 question bank click here to download

For CE6403 syllabus click here

CE6403 Note click here

For CE6403 important questions click here

CE6402 QUESTION BANK STRENGTH OF MATERIALS REGULATION 2013 ANNA UNIVERSITY

Post author By Mr. Padeepz
Post date February 25, 2018
No Comments on CE6402 QUESTION BANK STRENGTH OF MATERIALS REGULATION 2013 ANNA UNIVERSITY

CE6402 QUESTION BANK STRENGTH OF MATERIALS

CE6402 QUESTION BANK STRENGTH OF MATERIALS REGULATION 2013 ANNA UNIVERSITY

Sample for CE6402 question bank:

1. beam of span 4 m is cantilever and subjected to a concentrated load 10 kN at free end. Find the total strain energy stored. Take the Flexural rigidity is EI.
(AUC Apr/May 2010).

2. Write down Maxwell’s reciprocal theorem. (AUC Apr/May 2010)

3. Write down the expression for strain energy stored in a bar of cross sectional area A and length ‘l’ and subjected to a tensile load ‘W’. (AUC Nov/Dec 2010).

4. State Maxwell’s reciprocal theorem. (AUC Nov/Dec 2010, Apr/May 2011 & 2012).

5. State the principle of virtual work. (AUC Apr/May 2011)

6. State Castigliano’s first theorem. (AUC Nov/Dec 2011)

7. A beam 4m in length is simply supported at the ends and carries a UDL of 6 kN/m length over the entire length. Determine the strain energy stored in the beam. Take E = 200 GN/m2 and I = 1440 cm4.

8. A beam simply supported over a span of 3m carries a UDL of 20 kN/m over the entire span. Taking EI = 2.25 MNm2 and using Castigliano’s theorem, determine the deflection at the centre of the beam.

9. A continuous beam of two equal spans L is uniformly loaded over its entire length. Find the magnitude R of the middle reaction by using Castigliano’s theorem.

10. Determine the buckling load for a column of T section with flange of 100mm width and overall depth 120mm. Both flange and web are of 10mm thick. The strut is 3m long with one end hinged and other end fixed.

11. Determine the buckling load for a column of rectangular section of size 100mm width and overall depth 120mm. The strut is 3m long with one end hinged and other end fixed.

Subject Name	STRENGTH OF MATERIALS
Subject Code	CE6402
Regulation	2013
File	PDF

CE6402 question Bank 1 click here

CE6402 question Bank 2 click here

For CE6402 Important questions click here

CE6402 Syllabus Click here

For CE6402 Notes click here

CE6401 Question Bank CONSTRUCTION MATERIALS REGULATION 2013 Anna University

Post author By Mr. Padeepz
Post date February 23, 2018
No Comments on CE6401 Question Bank CONSTRUCTION MATERIALS REGULATION 2013 Anna University

CE6401 Question Bank CONSTRUCTION MATERIALS REGULATION 2013 Anna University

CE6401 Question Bank CONSTRUCTION MATERIALS REGULATION 2013 Anna University free pdf download.

Sample for CE6401 Question Bank:

1. Define seasoning of Timber.

2. List out the defects in timber.

3. What are the causes of decay of wood work?

4. What is veneer plywood?

5. Define annealling of steel.

6. Mention the market forms of steel.

7. What is anodizing of aluminium?

8. What are the available forms of aluminium?

9. Describe the composition of duralumin.

10. What are the methods through which galvanized coatings is given to GI sheets?

11. What are the paints commonly used in building construction?

12. Name the basic components of paints?

13. What is pigment volume concentration number?

14. What are the considerations in choosing paints?

15. Define distempers.

16. Mention the types of varnishes.

17. Differentiate between dry distemper and oil bound distemper.

18. Define covering capacity of paints.

19. Define blown bitumen.

20. What is penetration of bitumen?

21. What are the constituents of Glass?

22. What are the properties of Glass?

23. What are the uses of Glass?

24. What is the characteristic feature of ceramic materials?

25. What is Sealent and where it is used?

26. List the uses of ceramics?

27. Write a short note on FGRP?

28. What are the uses of FGRP?

29. Write any four properties of clay products?

30.What are the uses of Clay products?

31.State any four properties of Refractories?

32.Write a short note on Refractories?

33.What do you mean by composite materials?

34.What are the types of composite materials?

35.What are laminar composites?

36.What are the applications of laminar composites?

37.What is Geo Membrane?

38.What are the uses of Geo membrane?

Subject Name	CONSTRUCTION MATERIALS
Subject Code	CE6401
Regulation	2013
File Type	PDF

For CE6401 Question Bank Click here to download

CE6401 Syllabus Click here

CE6401 Notes click here

For CE6401 important questions click here

Other Links:

CE6402 Strength of Materials Syllabus Click here

CE6403 Applied Hydraulic Engineering Syllabus Click here

CE6404 Surveying II Syllabus Click here

CE6405 Soil Mechanics Syllabus Click here

question bank

MA6459 Question Bank NUMERICAL METHODS for Regulation 2013 Anna University

Post author By Mr. Padeepz
Post date February 23, 2018
No Comments on MA6459 Question Bank NUMERICAL METHODS for Regulation 2013 Anna University

MA6459 Question Bank NUMERICAL METHODS for Regulation 2013 Anna University

Sample for Ma6459 Question Bank:

1. Write sufficient condition for convergence of an iterative method
for Xf (AU –A/M 2010)

2. Write the procedure to find the numerically smallest eigenvalue
of a matrix by power method. (AU –A/M 2010)

3. To what kind of a matrix, can the Jacob’s method be applied to
obtain the eigenvalues of a matrix? (AU –N/D 2010)

4. What is the criterion for the convergence in Newton’s method?
(AU –A/M 2011), (NOV/DEC 2015)

5. By Gauss elimination method solve (AU –A/M 2011)

6. Solve Xe X by the method of iteration. (AU N/D 2011)

7. Using Newton’s method, find the root between 0 and 1 of
(AU N/D 2011)

8. Staten the order of convergence and the criterion for the
convergence in Newton’s method. (AU –A/M 2012)

9. Give two direct methods to solve a system of linear equation.
(AU –A/M 2012) (NOV/DEC 2015)

10. Write down the order of convergence and the condition for
convergence of fixed point iteration method. (AU –N/D 2012)

11. What are the advantages of iterative methods over direct
methods for solving a system of linear equations?
(AU –N/D 2012)

12. Find an iterative formula to find the reciprocal of a given
number ( (AU –M/J 2013)

13. What is the use power method? (AU –M/J 2013)

14. Form the divided difference table for the data and )85,4()40,3(),4,1(),1,0(
(AU-APR/MAY-2010)(N/D 2015).

15. Define a cubic spline S(x) which is commonly used for interpolation.
(AU-APR/MAY-2010)

16. When to use Newton’s forward interpolation and when to use Newton’s
backward interpolation? (AU-NOV/DEC-2010)

17. Write down the Newton-cote’s formula for the equidistant ordinates. (AUMAY/JUNE 2011)
18. When do you apply Simpson’s 1/3 rule ,and what is the order of the error
in Simpson’s 1/3 rule. (AU- MAY/JUNE 2011)