CE8395 Important Questions Strength of Materials for Mechanical Engineers
CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers Regulation 2017 Anna University free download. Strength of Materials for Mechanical Engineers Important 16 Marks Questions CE8395 pdf free download.
Sample CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers:
1. Three blanks of each 50 x200 mm timber are built up to a symmetrical I section for a beam. The maximum shear force over the beam is 4KN. Propose an alternate rectangular section of the same material so that the maximum shear stress developed is same in both sections. Assume then width of the section to be 2/3 of the depth. CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers
2. A beam of uniform section 10 m long carries a udl of 2KN/m for the entire length and a concentrated load of 10 KN at right end. The beam is freely supported at the left end. Find the position of the second support so that the maximum bending moment in the beam is as minimum as possible. Also compute the maximum bending moment CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers
3. A beam of size 150 mm wide, 250 mm deep carries a uniformly distributed load of w kN/m over entire span of 4 m. A concentrated load 1 kN is acting at a distance of 1.2 m from the left support. If the bending stress at a section 1.8 m from the left support is not to exceed 3.25 N/mm2 find the load w. CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers
4. A cantilever of 2m length carries a point load of 20 KN at 0.8 m from the fixed end and another point of 5 KN at the free end. In addition, a u.d.l. of 15 KN/m is spread over the entire length of the cantilever. Draw the S.F.D, and B.M.D. CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers
5. A Simply supported beam of effective span 6 m carries three point loads of 30 KN, 25 KN and 40 KN at 1m, 3m and 4.5m respectively from the left support. Draw the SFD and BMD. Indicating values at salient points. CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers
6. A Simply supported beam of length 6 metres carries a udl of 20KN/m throughout its length and a point of 30 KN at 2 metres from the right support. Draw the shear force and bending moment diagram. Also find the position and magnitude of maximum Bending moment. CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers
7. A Simply supported beam 6 metre span carries udl of 20 KN/m for left half of span and two point loads of 25 KN end 35 KN at 4 m and 5 m from left support. Find maximum SF and BM and their location drawing SF and BM diagrams.
8. A cantilever 1.5m long is loaded with a uniformly distribution load of 2 kN/m run over a length of 1.25m from the free end it also carries a point load of 3kn at a distance of 0.25m from the free end. Draw the shear force and bending moment diagram of the cantilever. CE8395 Important 16 Marks Questions Strength of Materials for Mechanical Engineers
9. For the simply supported beam loaded as shown in Fig. , draw the shear force diagram and bending moment diagram. Also, obtain the maximum bending moment.
| Subject name | STRENGTH OF MATERIALS FOR MECHANICAL ENGINEERS |
| Short Name | SMM |
| Semester | 4 |
| Subject Code | CE8395 |
| Regulation | 2017 regulation |
CE8395 Important 16 mark Questions Strength of Materials for Mechanical Engineers Click Here To Download
CE8395 Strength of Materials for Mechanical Engineers Syllabus
CE8395 Strength of Materials for Mechanical Engineers Notes
CE8395 Strength of Materials for Mechanical Engineers Question Bank
CE8395 Strength of Materials for Mechanical Engineers Question Paper